ConstructionDeal.com Update

After I discussed How to Install Bamboo Flooring, I realized I probably shouldn't leave you hanging on how to install your baseboards.

If you install bamboo, or just about any hardwood flooring, you'll more than likely need to install new baseboards. If you were able to carefully remove your original baseboards and they're in relatively good shape, you're lucky... it doesn't happen very often.

Baseboards need to be replaced when you go from carpet to hardwoods. Or when you go from a thick or thin hardwood to different size. The new flooring is going to go close to the wall and those old baseboards might be in the way (or too high up.)

What You'll Need:

• New baseboards, of course. Measure out the length of each wall and add those up. That will be the amount of linear feet you'll need to buy. Having some extra is always a good idea, in case you have problems or issues with length.
• Finishing nails. Depending on how thick your baseboards are, and how thick your drywall is, you'll most likely need nails that are 1 1/2 to 2 1/2 inches long. For my baseboards that I used with the bamboo flooring, the recommended length was 2 inches.
  
• Stud finder
• Mitre Saw
  
• Hammer
• Nail set
• Wood filler
• Sandpaper
• Paint

How to Install Baseboards
I purchased a primed fiberboard base for my room. You can buy un-primed wood or fiberboard and prime it yourself, as well. I recommend that you paint (or prime and paint) the baseboards before you install them. It's easier to do and means less of a chance that you'll accidentally paint your new floors or walls.

Measure your first wall. I started on the wall with the door entrance. I left one side at a 90 degree angle and this would butt up against the molding on the door. Measure out the entire length of that wall where it stops in a corner. At this corner, you'll want to use the mitre saw to cut a 45 degree angle.

Use the stud finder to find the wood studs underneath. At each stud, 16 inches apart, pound a finish nail through the baseboard and into the wall. Don't worry about pounding it down flush with the baseboard -- you could damage it.

On the next wall, measure and cut your baseboard. This time, you'll have a 45 degree angle on both ends. Use the stud finder and place your nails. Continue around your room until all your baseboards are installed.

If you get to a really long wall, longer than your baseboard length, you have two options:

• Cut a 90 degree butt joint and put the two baseboards together on the wall. It's hard to match them up and it may not look good. You'll see that seam in there just about every time.
  
• Cut a 45 degree angle where the bevel faces you. On the opposite baseboard, cut another 45 degree angle where the bevel faces your wall. This is a scarf joint. Those two 45 degree angles should match up to each other. Glue them together with wood glue. You can then put a nail in on both boards to hold them to the wall. A little filler, sanding, and paint and the joint should disappear.

After your boards are on, you may see a gap between the baseboard and the new flooring. It's a good idea to purchase some strips of Quarter Round molding. These pieces can be cut to length for that wall and hammered down with finish nails at a 45 degree angle. Again, try to prime and paint them before you start.

Use your nail set and hammer to pound the finish nails below the surface of the baseboards. Add wood filler to the holes. After the filler has dried (read the directions) you can lightly sand down the excess with sandpaper.

Finally, use your paint to cover up any exposed wood filler or any scratches created during installation. That's all there is to installing new baseboards.

Related Posts:
How to Install Bamboo Floors
Ready to Install Bamboo?

Do you need to install baseboards in your home, but this all sounds too complicated? Consider hiring a professional to do it for you. Our network of flooring pros can install floors and new baseboards for you.

It's easy to find a pro. Submit your request for free to ConstructionDeal.com. It's a fast way to find contractors.

Simply fill out a form and get calls from at least 4 local professionals. There is no cost or obligation. It saves you time - you won't have to call a bunch of people at random from the phone book. They will call you.

Labels: Bamboo Flooring, Baseboards, How To Install

Okay, so your floor prep has been done. Now you're ready to start installing the bamboo floors in your room.

I finished a 13 foot by 10 foot bedroom on Saturday. I did a little work on Friday evening to set everything up, but it's a job that can be completed in one whole day.

How to Install Bamboo Floors - Part Two
Here is a list of items you'll need to install your flooring:

• 15lb. Felt Paper Underlayment
• Bamboo Flooring (naturally...)
• A Floor Stapler
  
• An Air Compressor (to run your floor stapler)
• Flooring Staples (I used 2 inch crown staples for the 5/8" thick bamboo)
• A 10" or 12" mitre saw
• A Rubber Mallet (mine came with the Floor Stapler rental)
• Measuring Tape
• Hammer
• Finishing Nails
• Nail Set
• Chalk Line Set
• Matching Wood Filler

After the bamboo flooring has acclimated to your room for 3 to 7 days, and your subfloor is clean, you can begin installation.

Lay out the felt underlayment paper. Put it in the same direction your bamboo planks will go. Put down one row at a time to make sure you don't tear it up walking back and forth.

Start with the longest wall that is also an outside wall. Those tend to be the straightest walls. Use a chalk line to snap a straight-as-possible line along this wall. Place your first plank along that line, next to the wall. You'll have to nail it down with finishing nails. Try to nail the planks down to the floor joists underneath (you'll see a line of nails along in the subfloor where it was nailed to the joists.)

Note - Make sure you don't put the bamboo boards up tight against the walls. Give yourself a half inch or 5/8 inch gap between the wall and planks to allow for expansion and contraction of the bamboo. Your baseboards will cover the gaps (and if it's not enough, you can add an additional quarter-round to the baseboard.)

Fit your next plank in and nail it down. Continue along your wall until the row is completed. On your next row, stagger the lengths of your planks. You can either make it random or alternate lengths - you just don't want any of your seams to line up. You want the alternating look and you want the added strength.

Because your floor stapler won't fit, you'll have to nail down your first two or three rows. Use your nail set and hammer to hammer down the finish nails until they're below the surface of the bamboo.

Once you have room for the stapler, you can place your planks down and use the rubber mallet to pound the floor stapler to nail in the 2 inch staples. Put in a staple every 6 to 8 inches and not any closer than 2 inches to the edge of the plank. Tap your bamboo planks in with the mallet before a final staple to make sure you're eliminating gaps.

You may need to use a table saw to cut the planks length-wise once you get to the end of the room. It's rare that all the planks will fit in perfectly to every room. You may also need to remove the "tongue" on the planks to be able to drop those thinned boards in next to the wall.
One problem I had - when I first started, my air compressor was set to about 100 psi and it was causing the staples to go in very hard and crack the tongues on the bamboo boards (see pic below.) I backed the pressure down to below 95 psi and the splitting of the tongue stopped. Always test out a spare board before you begin to make sure you don't ruin too many planks.
I purchased matching bamboo T-moldings to transition from the bamboo to the carpet in the hallway. If you're going from bamboo to tile or laminate, you may need a bamboo "reducer" for your transitions. Nail those down with finishing nails and use the nail set to drop them out of sight.

The only thing left is to clean up and install your baseboards. You should prime and paint the baseboards before you nail them to your wall to make it easier (and avoid getting paint on your shiny new bamboo floor!)

RELATED POSTS:
Bamboo Flooring Preparation
Bamboo Countertops

Interested in putting bamboo in your home, but don't want to try it yourself?

You could hire a professional to do the work for you. Need to find a flooring installer? Submit your request for free to ConstructionDeal.com. It's a fast, easy way to find contractors.

Simply fill out a form and you'll get calls from a few local professionals. There is no cost or obligation. And it will save you time - you won't have to call a bunch of people at random from the phone book. They call you.

Labels: Bamboo, Flooring Options, How To Install

Not that kind of stud... A wall stud. Whenever possible, always try to secure shelves, mirrors, or other slightly heavy items into a wall stud. But, you know that...

What you might not know is how to find the stud. Sure, you can cheat and use one of the electronic stud finders -- you place it against the wall and move it along until it lights up when covering over a stud.

If you don't have one of those, you go "low tech." Studs are typically 16 inches, center to center. Remove one of the wall plates from a light switch or electrical socket -- usually the electrical boxes are mounted to a stud. Look to see if it's on the right or left hand side and measure 16 inches either way to find your stud.

You can also check your baseboards. Most baseboards are nailed directly into the studs. If it appears the nails are about 16 inches apart, you've more than likely got the location of the wall studs.

You might be able to remove a lamp shade from a lamp and shine the bare bulb on the walls -- drywall is normally screwed into the studs and it can leave a seam. You can move the lamp around to expose highlights to see those seams.

Sound like more than you want to bother with? Well, perhaps it's time to hire a handyman service. Go to ConstructionDeal.com and submit a request. You'll get 4 quotes from home repair services in the same day - sometimes within minutes.

There's no cost to use the service and there's no obligation.

Labels: Home Improvement, How To Install